Home.SiteBannerImage.Alt

지원되는 언어
Spellman 제품 파인더
사이트 검색
재설정 재설정
전압별 (kV)
전력별 (W)

도움이 필요하십니까?

도움이 필요하십니까?

원하시는 제품 검색에 어려움이 있으십니까? 기꺼이 도와드리겠습니다. 연락처 정보

카탈로그 다운로드

 Spellman Catalog

새로 보충된 Spellman의 153 페이지짜리 카탈로그는 고전압 산업 분야에서 가장 포괄적인 참고용 안내자료로서, 1.5W ~ 200kW 및 62V ~ 500kV규격의 70종류에 육박하는 여러 가지 전원장치 플랫폼들을 소개하였습니다.

저희 영어판 또는 일본어판 카탈로그를 다운로드하시려면 아래 바로가기 중 한 곳을 클릭하십시오.

: : 영어 (PDF 10 MB) 

스펠만하이볼테이지 기술 표준 매뉴얼

Need Help?

스펠만하이볼테이지 기술 표준 매뉴얼을 무료로 다운받으세요. FAQ, 응용분야 자료, 기술 자료, 용어집 등 다양한 자료가 있습니다.

: : 바로 다운로드   (PDF 14.0 MB)

AN-12

The Benefit of Using a Current Source to Power X-Ray Tube Filament Circuits

Virtually all the filament power supplies Spellman uses in their X-Ray generators and Monoblock® X-Ray sources are current sources...not voltage sources. That is, the filament power supply controls and regulates the current through the filament of the X-Ray tube. This is done to protect the filament and obtain the longest usage and lifetime of the X-Ray tube possible.

If a voltage source is used to power a filament then the current through the filament is dependent upon the impedance of the circuit. Cold filaments have a low impedance, as they heat up the impedance rises. So if you drive a filament with a voltage source you typically get a large spike of current at turn on…this is why most household incandescent light bulbs usually fail (blow out) at initial turn on.

With a current source filament power supply the current through the filament is always regulated, regardless of the impedance of the load. In fact, even if a short circuit was placed on the output, the current would still be regulated and limited to a safe level.

In this current regulated scenario “voltage” is not a critical factor. The voltage is nothing more than the compliance of the circuit. Whatever the impedance of the circuit is (filament resistance, cable and connecter resistance, etc.), this times the current flowing through the circuit will yield a voltage. As long as the current source filament power supply has more compliance voltage capability than the total circuit needs, all is fine.

The only time the “voltage limit circuit” could ever come into effect is if there is an open filament fault. In this case it’s basically a moot point, the filament is open…you can’t make X-Rays and the X-Ray tube requires replacement. Does it really matter if the open filament cable has 6 volts across it or 12 volts across it? No it doesn’t, the filament is open, and the X-Ray tube can’t function because you have an open filament circuit.

For this reason we don’t fuss much with voltage limit settings on filament power supplies. As long as there is enough compliance voltage to drive the effective filament load…all is fine. If the filament fails, the maximum open circuit sourcing voltage will limited to a safe and predictable level. With a current source filament power supply playing with the setting of the voltage limit circuit provides no real additional protection or benefit for the X-Ray tube.

Twitter facebook GooglePlus Tumblr Pinterest YouTube LinkedIn instagram

연락처 정보 | 홈페이지 | 회사 소개 | 사이트맵 | 개인 정보 보호 정책
Copyright © 2016, Spellman High Voltage Electronics Corporation | 475 Wireless Boulevard - Hauppauge, NY 11788 | Phone: +1 631 630 3000