Home.SiteBannerImage.Alt

지원되는 언어
Spellman 제품 파인더
사이트 검색
재설정 재설정
전압별 (kV)
전력별 (W)

도움이 필요하십니까?

도움이 필요하십니까?

원하시는 제품 검색에 어려움이 있으십니까? 기꺼이 도와드리겠습니다. 연락처 정보

카탈로그 다운로드

 Spellman Catalog

새로 보충된 Spellman의 153 페이지짜리 카탈로그는 고전압 산업 분야에서 가장 포괄적인 참고용 안내자료로서, 1.5W ~ 200kW 및 62V ~ 500kV규격의 70종류에 육박하는 여러 가지 전원장치 플랫폼들을 소개하였습니다.

저희 영어판 또는 일본어판 카탈로그를 다운로드하시려면 아래 바로가기 중 한 곳을 클릭하십시오.

: : 영어 (PDF 10 MB) 

스펠만하이볼테이지 기술 표준 매뉴얼

Need Help?

스펠만하이볼테이지 기술 표준 매뉴얼을 무료로 다운받으세요. FAQ, 응용분야 자료, 기술 자료, 용어집 등 다양한 자료가 있습니다.

: : 바로 다운로드   (PDF 14.0 MB)

AN-21

How to Calculate Maximum AC Input Current
Knowing a power supplies maximum input current can be helpful in selecting electrical service requirements, circuit breaker selection, AC input cable and connector selection and even picking an isolation transformer in floating applications. Calculating the maximum input current is fairly easy knowing a few basic parameters and some simple math.

High Voltage Power Supply Power Rating
All of Spellman’s power supplies have an advertised maximum power rating, in watts. This is the first parameter we’ll need and it can be obtained from the product data sheet. Most of Spellman’s power supplies have the maximum power rating right in the model number. Like for this example an SL30P300/115 is a 30kV, positive polarity unit that can provide 300 watts, maximum; operated from 115Vac input line.

Power Supply Efficiency
The power supplies efficiency is the ratio of input power to output power. Efficiency is typically stated as a percentage or a decimal less than 1, like 80% or 0.8. To figure out the input power we take the stated maximum output power and divide by the efficiency:

300 watts / 0.8 = 375 watts

Power Factor
Power factor is the ratio of the real power to apparent power utilized. It is typically expressed as a decimal number less than 1. Real power is expressed in watts while apparent power is expressed in VA (volt-amperes). Single phase uncorrected switching power supplies typically have fairly poor power factor, like 0.65. Three phase uncorrected switching power supplies have a higher power factor, like 0.85. Units with active power factor correction circuitry can have very good power factor like 0.98. In our example above the supply is an uncorrected unit, powered by a single phase line so:

375 watts / 0.65 = 577 VA

Input Line Voltage
We need to know the AC input voltage the unit is designed to be powered from. In the example above the AC input voltage is 115Vac. This is the nominal voltage, in reality the input voltage is specified at ±10%. We need to subtract 10% to account for the worst case, low line condition:

115Vac – 10% = 103.5Vac

Maximum AC Input Current
If we take the 577 VA and divide it by 103.5Vac we get:

577 VA / 103.5Vac = 5.57 amps

If our AC input voltage is single phase, then we have our answer, 5.57 amps.

Three Phase Input Voltage
Units with three phase input voltage are powered by three phases, hence they have a better power factor number than single phase units. Also due to the presence of three phases powering the unit, phase currents will be less. To obtain the input current per phase we divide our input current calculation by √3 (1.73).

Let’s calculate this example: STR10N6/208. From the STR data sheet we find out the maximum power is 6000 watts, the efficiency is 90% and the power factor is 0.85. Although the STR will operate down to 180Vac by design, in this example it will be powered via 208Vac, 3 phase. We obtain the maximum input current per phase as follows:

Power Supply Efficiency
6000 watts / .9 = 6666 watts

Power Factor
6666 watts / .85 = 7843 VA

Input Line Voltage
208Vac – 10% = 187Vac

Maximum AC Input Current
7843 VA / 187Vac = 41.94 amps (if it was single phase)

Correction for Three Phase Input
41.94 amps / √3 (1.73) = 24.21 amps per phase

So we have two equations, one for single phase inputs and one for three phase inputs:

Single Phase Maximum Input Current Equation
Input Current = Maximum Power/(Efficiency)(Power Factor)(Minimum Input Voltage)

Three Phase Maximum Input Current Equation
Input Current = Maximum Power/(Efficiency)(Power Factor)(Minimum Input Voltage)(√3)

These input current calculations are for the worst case: assuming the unit is running at maximum power, operating at a low line condition and taking efficiency and power factor into account.
Twitter facebook GooglePlus Tumblr Pinterest YouTube LinkedIn instagram

연락처 정보 | 홈페이지 | 회사 소개 | 사이트맵 | 개인 정보 보호 정책
Copyright © 2016, Spellman High Voltage Electronics Corporation | 475 Wireless Boulevard - Hauppauge, NY 11788 | Phone: +1 631 630 3000